Equal Angle Steel (L25×25 – L200×200) | Q235B, Q355B, SS400
Hot-rolled equal-leg angle steel from L25×25 up to L200×200 in Q235B, Q355B and SS400, supplied in 6 m, 9 m and 12 m lengths and cut, punched or drilled to your cutting list on request. Mill test certificate with every heat, export packing for container or bulk vessel, and trial quantities from one ton.
Product Overview
Equal angle steel — also called equal-leg angle, L-angle or angle iron — is a hot-rolled section with two legs of identical width set at 90 degrees. It is the most versatile and lowest-cost structural profile in the trade: it resists bending in both directions, it welds, drills, punches and bends without difficulty, and two or four angles can be bolted or welded back-to-back into a compound member when a single angle is not stiff enough.
The section is defined by leg width and leg thickness, written as L plus the leg width, for example L50×50×5. Stock covers the light-to-heavy range from L25×25 up to L200×200 with the standard thicknesses rolled in each size. Standard mill lengths are 6 m, 9 m and 12 m; we also cut to length, punch and drill to your fabrication drawing so the finished member arrives ready to erect rather than ready to rework.
Three grades cover almost every enquiry: Q235B to GB/T 700 for general structural and fabrication work, Q355B to GB/T 1591 where the higher yield strength lets you use a lighter section, and SS400 to JIS G3101 for buyers who work to Japanese standards. A mill test certificate showing heat number, chemical composition and mechanical properties travels with every lot, and grade equivalence to ASTM or EN grades is confirmed in writing before shipment.

Specifications & Size Range
Equal-leg stock range with the leg thicknesses normally produced in each size group. Mill lengths are 6 m, 9 m and 12 m; cut-to-length, punched and drilled processing is available. Send the drawing or cutting list and we will confirm availability in the exact size and thickness you need.
| Size group | Common sizes (mm) | Leg thickness (mm) | Standard length | Typical use |
|---|---|---|---|---|
| Light angle | L25×25, L30×30, L40×40 | 3 / 4 / 5 | 6 m | Framing, brackets, shelving, light supports |
| Medium angle | L50×50, L63×63, L75×75 | 4 / 5 / 6 / 8 | 6 m / 9 m / 12 m | Bracing, purlins, plant supports, mezzanine members |
| Heavy angle | L90×90, L100×100, L125×125 | 8 / 10 / 12 | 9 m / 12 m | Tower legs, bridge members, machine bases |
| Large angle | L140×140, L150×150, L160×160, L200×200 | 10 / 12 / 14 / 16 / 20 | 9 m / 12 m | Heavy frames, gantries, structural nodes |
| Processed angle | Any size above | as above | cut to drawing | Punched, drilled or mitred members ready for erection |
Tolerances
Dimensions, mass, out-of-square and longitudinal bow follow GB/T 706 (hot-rolled section steel), and the applicable tolerance band is stated on the mill certificate and repeated on the order acknowledgement. Where a tighter tolerance is needed — for example on a member that has to fit an existing bolted connection — state the requirement on the enquiry and we will confirm in writing what the mill can hold on that size.
Available Sizes — Detailed Specification
Every size below has its own page with the full theoretical weight table, tolerances, grade data, applications and delivery options. Theoretical weights are the published values from GB/T 706-2016 Table A.3.
20–60 mm leg
| Size | Thickness | Weight (kg/m) | Specification page |
|---|---|---|---|
| 20 × 20 mm | 3 mm | 0.889 | Weight & specification |
| 20 × 20 mm | 4 mm | 1.145 | Weight & specification |
| 25 × 25 mm | 3 mm | 1.124 | Weight & specification |
| 25 × 25 mm | 4 mm | 1.459 | Weight & specification |
| 30 × 30 mm | 3 mm | 1.373 | Weight & specification |
| 30 × 30 mm | 4 mm | 1.787 | Weight & specification |
| 36 × 36 mm | 3 mm | 1.656 | Weight & specification |
| 36 × 36 mm | 4 mm | 2.163 | Weight & specification |
| 36 × 36 mm | 5 mm | 2.655 | Weight & specification |
| 40 × 40 mm | 3 mm | 1.852 | Weight & specification |
| 40 × 40 mm | 4 mm | 2.423 | Weight & specification |
| 40 × 40 mm | 5 mm | 2.977 | Weight & specification |
| 45 × 45 mm | 3 mm | 2.087 | Weight & specification |
| 45 × 45 mm | 4 mm | 2.737 | Weight & specification |
| 45 × 45 mm | 5 mm | 3.369 | Weight & specification |
| 45 × 45 mm | 6 mm | 3.985 | Weight & specification |
| 50 × 50 mm | 3 mm | 2.332 | Weight & specification |
| 50 × 50 mm | 4 mm | 3.059 | Weight & specification |
| 50 × 50 mm | 5 mm | 3.77 | Weight & specification |
| 50 × 50 mm | 6 mm | 4.465 | Weight & specification |
| 56 × 56 mm | 3 mm | 2.624 | Weight & specification |
| 56 × 56 mm | 4 mm | 3.446 | Weight & specification |
| 56 × 56 mm | 5 mm | 4.251 | Weight & specification |
| 56 × 56 mm | 6 mm | 5.04 | Weight & specification |
| 56 × 56 mm | 7 mm | 5.812 | Weight & specification |
| 56 × 56 mm | 8 mm | 6.568 | Weight & specification |
| 60 × 60 mm | 5 mm | 4.576 | Weight & specification |
| 60 × 60 mm | 6 mm | 5.427 | Weight & specification |
| 60 × 60 mm | 7 mm | 6.262 | Weight & specification |
60–90 mm leg
| Size | Thickness | Weight (kg/m) | Specification page |
|---|---|---|---|
| 60 × 60 mm | 8 mm | 7.081 | Weight & specification |
| 63 × 63 mm | 4 mm | 3.908 | Weight & specification |
| 63 × 63 mm | 5 mm | 4.822 | Weight & specification |
| 63 × 63 mm | 6 mm | 5.721 | Weight & specification |
| 63 × 63 mm | 7 mm | 6.603 | Weight & specification |
| 63 × 63 mm | 8 mm | 7.469 | Weight & specification |
| 63 × 63 mm | 10 mm | 9.153 | Weight & specification |
| 70 × 70 mm | 4 mm | 4.372 | Weight & specification |
| 70 × 70 mm | 5 mm | 5.398 | Weight & specification |
| 70 × 70 mm | 6 mm | 6.406 | Weight & specification |
| 70 × 70 mm | 7 mm | 7.398 | Weight & specification |
| 70 × 70 mm | 8 mm | 8.376 | Weight & specification |
| 75 × 75 mm | 5 mm | 5.818 | Weight & specification |
| 75 × 75 mm | 6 mm | 6.906 | Weight & specification |
| 75 × 75 mm | 7 mm | 7.976 | Weight & specification |
| 75 × 75 mm | 8 mm | 9.03 | Weight & specification |
| 75 × 75 mm | 9 mm | 10.072 | Weight & specification |
| 75 × 75 mm | 10 mm | 11.092 | Weight & specification |
| 80 × 80 mm | 5 mm | 6.211 | Weight & specification |
| 80 × 80 mm | 6 mm | 7.377 | Weight & specification |
| 80 × 80 mm | 7 mm | 8.525 | Weight & specification |
| 80 × 80 mm | 8 mm | 9.656 | Weight & specification |
| 80 × 80 mm | 9 mm | 10.778 | Weight & specification |
| 80 × 80 mm | 10 mm | 11.877 | Weight & specification |
| 90 × 90 mm | 6 mm | 8.352 | Weight & specification |
| 90 × 90 mm | 7 mm | 9.656 | Weight & specification |
| 90 × 90 mm | 8 mm | 10.943 | Weight & specification |
| 90 × 90 mm | 9 mm | 12.222 | Weight & specification |
| 90 × 90 mm | 10 mm | 13.478 | Weight & specification |
90–150 mm leg
| Size | Thickness | Weight (kg/m) | Specification page |
|---|---|---|---|
| 90 × 90 mm | 12 mm | 15.943 | Weight & specification |
| 100 × 100 mm | 6 mm | 9.365 | Weight & specification |
| 100 × 100 mm | 7 mm | 10.833 | Weight & specification |
| 100 × 100 mm | 8 mm | 12.277 | Weight & specification |
| 100 × 100 mm | 9 mm | 13.706 | Weight & specification |
| 100 × 100 mm | 10 mm | 15.119 | Weight & specification |
| 100 × 100 mm | 12 mm | 17.898 | Weight & specification |
| 100 × 100 mm | 14 mm | 20.614 | Weight & specification |
| 100 × 100 mm | 16 mm | 23.26 | Weight & specification |
| 110 × 110 mm | 7 mm | 11.932 | Weight & specification |
| 110 × 110 mm | 8 mm | 13.533 | Weight & specification |
| 110 × 110 mm | 10 mm | 16.689 | Weight & specification |
| 110 × 110 mm | 12 mm | 19.782 | Weight & specification |
| 110 × 110 mm | 14 mm | 22.812 | Weight & specification |
| 125 × 125 mm | 8 mm | 15.504 | Weight & specification |
| 125 × 125 mm | 10 mm | 19.13 | Weight & specification |
| 125 × 125 mm | 12 mm | 22.694 | Weight & specification |
| 125 × 125 mm | 14 mm | 26.195 | Weight & specification |
| 125 × 125 mm | 16 mm | 29.626 | Weight & specification |
| 140 × 140 mm | 10 mm | 21.485 | Weight & specification |
| 140 × 140 mm | 12 mm | 25.52 | Weight & specification |
| 140 × 140 mm | 14 mm | 29.492 | Weight & specification |
| 140 × 140 mm | 16 mm | 33.394 | Weight & specification |
| 150 × 150 mm | 8 mm | 18.644 | Weight & specification |
| 150 × 150 mm | 10 mm | 23.055 | Weight & specification |
| 150 × 150 mm | 12 mm | 27.404 | Weight & specification |
| 150 × 150 mm | 14 mm | 31.69 | Weight & specification |
| 150 × 150 mm | 15 mm | 33.802 | Weight & specification |
| 150 × 150 mm | 16 mm | 35.906 | Weight & specification |
160–250 mm leg
| Size | Thickness | Weight (kg/m) | Specification page |
|---|---|---|---|
| 160 × 160 mm | 10 mm | 24.728 | Weight & specification |
| 160 × 160 mm | 12 mm | 29.39 | Weight & specification |
| 160 × 160 mm | 14 mm | 33.99 | Weight & specification |
| 160 × 160 mm | 16 mm | 38.52 | Weight & specification |
| 180 × 180 mm | 12 mm | 33.158 | Weight & specification |
| 180 × 180 mm | 14 mm | 38.386 | Weight & specification |
| 180 × 180 mm | 16 mm | 43.544 | Weight & specification |
| 180 × 180 mm | 18 mm | 48.639 | Weight & specification |
| 200 × 200 mm | 14 mm | 42.892 | Weight & specification |
| 200 × 200 mm | 16 mm | 48.678 | Weight & specification |
| 200 × 200 mm | 18 mm | 54.401 | Weight & specification |
| 200 × 200 mm | 20 mm | 60.06 | Weight & specification |
| 200 × 200 mm | 24 mm | 71.168 | Weight & specification |
| 220 × 220 mm | 16 mm | 53.906 | Weight & specification |
| 220 × 220 mm | 18 mm | 60.249 | Weight & specification |
| 220 × 220 mm | 20 mm | 66.537 | Weight & specification |
| 220 × 220 mm | 22 mm | 72.754 | Weight & specification |
| 220 × 220 mm | 24 mm | 78.892 | Weight & specification |
| 220 × 220 mm | 26 mm | 85.016 | Weight & specification |
| 250 × 250 mm | 18 mm | 68.954 | Weight & specification |
| 250 × 250 mm | 20 mm | 76.184 | Weight & specification |
| 250 × 250 mm | 22 mm | 83.367 | Weight & specification |
| 250 × 250 mm | 24 mm | 90.432 | Weight & specification |
| 250 × 250 mm | 26 mm | 97.497 | Weight & specification |
| 250 × 250 mm | 28 mm | 104.405 | Weight & specification |
| 250 × 250 mm | 30 mm | 111.313 | Weight & specification |
| 250 × 250 mm | 32 mm | 118.142 | Weight & specification |
| 250 × 250 mm | 35 mm | 128.269 | Weight & specification |
Steel Grades & International Equivalents
All grades below are supplied with a mill test certificate. The right-hand column shows the material type and the Chinese standard the grade is produced to; the middle columns give the nearest recognised equivalent in other national standards. Exact equivalence for a specific project should be confirmed on the enquiry.
| GB (China) | ASTM / AISI (US) | EN (Europe) | JIS (Japan) | DIN (Germany) | Type / Standard |
|---|---|---|---|---|---|
| Q235B | A36 / A283 Gr.C | S235JR (EN 10025-2) | SS400 (JIS G3101) | St37-2 | Carbon structural steel (GB/T 700) |
| Q355B | A572 Gr.50 / A992 | S355JR (EN 10025-2) | SM490 (JIS G3106) | St52-3 | High-strength low-alloy (HSLA) steel (GB/T 1591) |
| SS400 (JIS) | A36 | S235JR | SS400 | St37-2 | Carbon structural steel (JIS G3101) |
Grade Notes
- Q235B — The workhorse structural grade in China. Fully weldable, excellent cost-performance, the closest Chinese equivalent to ASTM A36 / EN S235JR.
- Q355B — High-strength structural steel for heavy structures, bridges and towers. Equivalent to ASTM A572 Gr.50 / EN S355JR.
- SS400 (JIS) — Japanese standard grade widely accepted in Asia. Interchangeable with Q235B / A36 for general structures.
Chemical Composition (%, ladle analysis)
Typical specification limits. Actual heat values are reported on the mill test certificate supplied with every shipment.
| Grade | C | Si | Mn | P max | S max | Other elements |
|---|---|---|---|---|---|---|
| Q235B | ≤0.20 | ≤0.35 | ≤1.40 | ≤0.045 | ≤0.045 | — |
| Q355B | ≤0.24 | ≤0.55 | ≤1.60 | ≤0.035 | ≤0.035 | Ceq ≤0.45 |
| SS400 (JIS) | — | — | — | ≤0.050 | ≤0.050 | — |
Mechanical Properties
Minimum values at room temperature unless stated. ReL = yield strength; Rp0.2 = 0.2% proof stress; Rm = tensile strength; A = elongation after fracture.
| Grade | Yield (ReL) | Proof (Rp0.2) | Tensile (Rm) | Elongation A | Impact / others | |
|---|---|---|---|---|---|---|
| Q235B | ≥235 MPa | — | 370–500 MPa | ≥26% | +20 °C, ≥27 J | — |
| Q355B | ≥355 MPa (≤16 mm) | — | 470–630 MPa | ≥22% | +20 °C, ≥27 J | — |
| SS400 (JIS) | ≥245 MPa | — | 400–510 MPa | ≥21% | — | — |

Standards & Documents
- GB/T 706 — hot-rolled section steel (angle dimensions, shape, mass and tolerance)
- GB/T 700 — carbon structural steels (Q235B: ReH ≥ 235 MPa)
- GB/T 1591 — high-strength low-alloy structural steels (Q355B: ReH ≥ 355 MPa)
- JIS G3101 — rolled steels for general structure (SS400)
- EN 10025-2 / ASTM A36 / A572 Gr.50 — grade equivalences confirmed in writing on request
- EN 10204 3.1 mill test certificate with every lot; SGS or BV third-party inspection on request
Typical Applications
| Industry / Application | Typical use |
|---|---|
| Transmission towers & substation structures | Tower legs, bracing, cross-arms and cable supports, plus transformer and switchgear frames. Angles for this duty are normally supplied hot-dip galvanized. |
| Solar & PV mounting structures | Ground-mount and rooftop racking, purlins and rail supports, where a light section with a predictable bending capacity keeps both steel weight and freight cost down. |
| Building frames & secondary steelwork | Purlins, wall bracing, lintels, plant-room frames, mezzanine members and duct or pipe supports in commercial and industrial buildings. |
| Bridges & road infrastructure | Guard-rail posts, pedestrian barriers, sign gantries, drainage gratings and small bridge members, supplied cut and drilled to the fabrication drawing. |
| Machinery frames & equipment bases | Frames and bases for conveyors, compressors, tanks and skids, where the angle can be welded directly to plate without special preparation. |
| Shelving, racks & workshop fabrication | Storage racks, work benches, display frames and general workshop fabrication, in mill finish or galvanized. |
| Marine & coastal structures | Jetty works, port equipment frames, sea-wall reinforcement and fish-farm cages, where the section is hot-dip galvanized for salt-spray service. |
Common Problems Buyers Face — and How We Prevent Them
These are the issues that most often cause claims on steel imports. Each one is controlled in our process before shipment.
Surface rust appearing before the steel is fabricated
Why it happens: Hot-rolled angle is shipped with mill scale and no coating, so humid air or a long sea voyage will start surface oxidation within days of leaving the mill.
Our control: Bundles are shipped dry and covered, and VCI paper with desiccant is included on long or humid routes. For rust-critical projects we supply pickled and oiled, primed, or hot-dip galvanized angle instead of mill finish.
Leg thickness running under the nominal value
Why it happens: Cheap material can be rolled to the minus side of the standard tolerance, and the loss of section is only noticed when the member is checked against the design drawing.
Our control: We buy mill-certified sections only and confirm the thickness tolerance band in writing before shipment. Negative-tolerance stock is never shipped as standard material, and the mill certificate backs up what arrives on site.
Long slender angles arriving bowed or twisted
Why it happens: Thin-wall light angles are flexible, and stacking or handling without support during transhipment will bend a 12 m member.
Our control: Long light angles are bundled into a stiff pack, supported along their length during loading and lashed so the bundle cannot sag. Straightness is checked at loading against the standard and reported on the inspection record.
Cracking in a cold bend, or a weld that fails inspection
Why it happens: The wrong strength grade has been chosen for the process, or a high carbon-equivalent steel has been used where cold forming or unrestricted welding is required.
Our control: We match the grade to the operation: Q235B or SS400 for cold bending and general welding, Q355B where strength governs and the welding procedure is controlled. If your drawing names a grade you cannot source, send it to us and we will propose a documented equivalent.
Mixed sizes in one bundle on site
Why it happens: Adjacent angle sizes look almost identical in mill finish, so picking errors happen at the yard and are discovered when the connection will not line up.
Our control: Every bundle is tagged by size, heat number and grade, and packed in cutting-list sequence where the order allows. Labels show the section designation in millimetres, so a receiving check needs a tape measure rather than a standard.

Our Supply & Manufacturing Advantages
- The full size range from one source — L25×25 up to L200×200 on a single order, so you are not combining three suppliers and three certificate sets on one shipment.
- Grade equivalence handled for you — Tell us the drawing grade — A36, S235JR, S355JR, SS400 — and we will nominate the Chinese grade, confirm the equivalence in writing and ship the certificate that matches.
- Processing before shipment — Cutting to length, punching, drilling and mitring are done before packing, which cuts offcut waste, freight weight and site labour.
- Documented material — EN 10204 3.1 mill test certificate with heat number, composition and mechanical properties for every lot, plus third-party inspection when your project requires it.
- Export packaging built in — Bundled and strapped to container dimensions, or shipped loose in a bulk vessel, with end and edge protection so the material arrives square and undamaged.
- Trial quantities welcome — No strict minimum order quantity: one ton can ship, which makes a first order or a small maintenance job practical.
Packaging, Delivery & Payment
- Packing: loose in bulk vessel, or bundled and containerised to your requirement. Galvanized and coated products get VCI paper, waterproof wrapping and edge protection. See our export packaging methods.
- Availability: both stock and custom production. Tell us the specification and we will confirm the route.
- MOQ: no strict minimum — one ton can ship.
- Lead time: stock dispatched to port within 3 days; orders needing export packaging about 1 week; custom production quoted per product.
- Payment: stock — 10% deposit, balance before shipment; custom production — 50% deposit, balance before shipment.
- Documents: EN 10204 3.1 mill test certificate with every shipment; third-party inspection (SGS / BV) on request.
Frequently Asked Questions
What is the Chinese equivalent of EN S235JR angle steel?
Q235B to GB/T 700 is the closest Chinese equivalent to S235JR, matching closely on yield strength, tensile range and impact requirement at +20 °C. For S355JR the equivalent is Q355B to GB/T 1591, with a minimum yield of 355 MPa at thicknesses up to 16 mm. If your drawing names the EN grade, we will supply the Chinese grade and confirm the equivalence in writing with the mill certificate.
What is the difference between equal angle and unequal angle steel?
Equal angle has two legs of the same width, so its stiffness is the same in both directions and it suits symmetric load paths such as bracing, purlins and tower members. Unequal angle has one long and one short leg, which puts more material where the load acts and gives a lighter answer for asymmetric brackets and one-sided supports. If the load is not symmetric, unequal angle usually saves weight.
Should I specify Q235B or Q355B for angle steel?
Q235B is the economical choice for general frames, bracing, brackets and fabrication where a standard structural grade is sufficient. Q355B is chosen when a heavier load must be carried by a lighter or thinner section, when a longer span is required, or when the specification calls for a 355 MPa minimum yield. Because Q355B carries a carbon-equivalent limit of 0.45, tell us the welding procedure so we can confirm it is suitable.
Is SS400 the same as Q235B?
They are close but not identical. SS400 to JIS G3101 has a minimum tensile strength of 400 MPa and a minimum yield of 245 MPa, while Q235B has a minimum yield of 235 MPa and a tensile range of 370 to 500 MPa. Both are fully weldable general structural grades and are widely treated as interchangeable for ordinary structures. If your drawing names SS400 specifically, we will ship SS400 and certificate it as such.
Who supplies equal angle steel from China for export projects?
We do, and we supply it as an export order rather than a domestic one: grade equivalence confirmed before the order, EN 10204 3.1 mill certificate, third-party inspection if you want it, and export packing designed for container or bulk vessel. Send the section list, the grade and the destination port and you will get a quotation with the weight, the packing and the lead time.
Do you have a minimum order quantity?
No strict minimum. One ton can ship, which suits a trial order or a small maintenance job. For very small quantities the freight cost per ton will dominate the landed price, and we will tell you honestly where the break point is between container and less-than-container shipment.
Can you cut, punch and drill the angle before shipment?
Yes. Send the fabrication drawing or cutting list with hole positions and we will quote the processed member. Processing before shipment reduces offcut waste and removes site labour, and it also means the finished part can be galvanized after processing so no bare steel is left in the holes.
What documents come with an angle steel shipment?
An EN 10204 3.1 mill test certificate showing heat number, chemical composition and mechanical properties, plus the commercial invoice, packing list, bill of lading and certificate of origin. Mill certificates for each heat can be collated to match your cutting list or your bundle numbering, and SGS or BV inspection can be arranged before loading.
What is the lead time and how is the material packed?
Common sizes are dispatched to the port within 3 days of order confirmation. Orders that need export packing, cutting or punching take about one week to reach the port, and non-standard sizes are quoted item by item. Bundles are strapped to container dimensions with edge protection, or shipped loose in a bulk vessel for large tonnage.
Request a Quotation Export Packaging
Live Stock & Indicative Price
The table below lists live stock at the time of publication, with indicative EXW China reference prices in USD per tonne (converted at 6.70 CNY/USD). Steel prices move with the mill market every week — send us your size, quantity and destination and we will confirm availability and issue a firm FOB or CIF quotation.
| Product | Size / Model | Grade | Weight / pc | Price (USD/t, EXW) | Stock |
|---|---|---|---|---|---|
| Equal Angle Steel | L25×25 | Q235B | 4–4.5 kg | $524 | 2 |
| Equal Angle Steel | L25×25 | Q235B | 5–5.5 kg | $509 | 1 |
| Equal Angle Steel | L25×25 | Q235B | 6–6.5 kg | $509 | 6 |
| Equal Angle Steel | L30×30 | Q235B | 4–4.5 kg | $524 | 9 |
| Equal Angle Steel | L30×30 | Q235B | 5.5–6 kg | $504 | 2 |
| Equal Angle Steel | L30×30 | Q235B | 5–5.5 kg | $509 | 8 |
| Equal Angle Steel | L30×30 | Q235B | 6.5–7 kg | $497 | 3 |
| Equal Angle Steel | L30×30 | Q235B | 6–6.5 kg | $497 | 10 |
| Equal Angle Steel | L30×30 | Q235B | 7.5–8 kg | $497 | 4 |
| Equal Angle Steel | L30×30 | Q235B | 7–7.5 kg | $497 | 14 |
| Equal Angle Steel | L30×30 | Q235B | 8–8.5 kg | $497 | 4 |
| Equal Angle Steel | L30×30 | Q235B | 9–9.5 kg | $497 | 6 |
| Equal Angle Steel | L40×40 | Q235B | 10–10.5 kg | $490 | 9 |
| Equal Angle Steel | L40×40 | Q235B | 11–11.5 kg | $487 | 5 |
| Equal Angle Steel | L40×40 | Q235B | 12.5kg | $497 | 1 |
| Equal Angle Steel | L40×40 | Q235B | 12–12.5 kg | $487 | 8 |
| Equal Angle Steel | L40×40 | Q235B | 13–13.5 kg | $487 | 1 |
| Equal Angle Steel | L40×40 | Q235B | 14–14.5 kg | $490 | 4 |
| Equal Angle Steel | L40×40 | Q235B | 16–16.5 kg | $494 | 2 |
| Equal Angle Steel | L40×40 | Q235B | 6–6.5 kg | $507 | 3 |
| Equal Angle Steel | L40×40 | Q235B | 8–8.5 kg | $496 | 1 |
| Equal Angle Steel | L40×40 | Q235B | 9–9.5 kg | $493 | 7 |
| Equal Angle Steel | 45 × 4 mm | Q235B | 14.5–15 kg | $487 | 2 |
| Equal Angle Steel | 45 × 5 mm | Q235B | 18–19 kg | $487 | 3 |
| Equal Angle Steel | L50×50 | Q235B | 10–10.5 kg | $510 | 3 |
| Equal Angle Steel | L50×50 | Q235B | 11–11.5 kg | $503 | 4 |
| Equal Angle Steel | L50×50 | Q235B | 12–12.5 kg | $493 | 3 |
| Equal Angle Steel | L50×50 | Q235B | 13–13.5 kg | $490 | 2 |
| Equal Angle Steel | L50×50 | Q235B | 14–14.5 kg | $490 | 1 |
| Equal Angle Steel | L50×50 | Q235B | 15–15.5 kg | $488 | 6 |
| Equal Angle Steel | L50×50 | Q235B | 16–16.5 kg | $488 | 5 |
| Equal Angle Steel | L50×50 | Q235B | 17–17.5 kg | $485 | 8 |
| Equal Angle Steel | L50×50 | Q235B | 18–18.5 kg | $485 | 8 |
| Equal Angle Steel | L50×50 | Q235B | 19–19.5 kg | $485 | 1 |
| Equal Angle Steel | L50×50 | Q235B | 20–20.5 kg | $485 | 1 |
| Equal Angle Steel | L50×50 | Q235B | 21–21.5 kg | $485 | 10 |
| Equal Angle Steel | L50×50 | Q235B | 22–22.5 kg | $485 | 3 |
| Equal Angle Steel | L50×50 | Q235B | 24–25 kg | $490 | 3 |
| Equal Angle Steel | 56 × 4 mm | Q235B | 19.0kg | $487 | 4 |
| Equal Angle Steel | 56 × 5 mm | Q235B | 23–24 kg | $487 | 3 |
| Equal Angle Steel | L63×63 | Q235B | 20–20.5 kg | $504 | 10 |
| Equal Angle Steel | L63×63 | Q235B | 21–21.5 kg | $499 | 7 |
| Equal Angle Steel | L63×63 | Q235B | 22–22.5 kg | $493 | 3 |
| Equal Angle Steel | L63×63 | Q235B | 23–23.5 kg | $490 | 2 |
| Equal Angle Steel | L63×63 | Q235B | 24.5–25 kg | $487 | 1 |
| Equal Angle Steel | L63×63 | Q235B | 24–24.5 kg | $487 | 3 |
| Equal Angle Steel | L63×63 | Q235B | 25–25.5 kg | $485 | 3 |
| Equal Angle Steel | L63×63 | Q235B | 26–26.5 kg | $485 | 1 |
| Equal Angle Steel | L63×63 | Q235B | 27–27.5 kg | $485 | 8 |
| Equal Angle Steel | L63×63 | Q235B | 28–28.5 kg | $485 | 4 |
| Equal Angle Steel | L63×63 | Q235B | 29.57kg | $485 | 3 |
| Equal Angle Steel | L63×63 | Q235B | 29.67kg | $485 | 1 |
| Equal Angle Steel | L63×63 | Q235B | 29–29.5 kg | $485 | 1 |
| Equal Angle Steel | L63×63 | Q235B | 30–30.5 kg | $485 | 3 |
| Equal Angle Steel | L63×63 | Q235B | 31–31.5 kg | $485 | 4 |
| Equal Angle Steel | L63×63 | Q235B | 32–32.5 kg | $485 | — |
| Equal Angle Steel | L63×63 | Q235B | 40–42 kg | $496 | 2 |
| Equal Angle Steel | 70 × 5 mm | Q235B | 26–27 kg | $487 | 3 |
| Equal Angle Steel | 70 × 5 mm | Q235B | 29–30 kg | $487 | 3 |
| Equal Angle Steel | 70 × 6 mm | Q235B | 31–32 kg | $487 | 1 |
| Equal Angle Steel | 70 × 6 mm | Q235B | 34–35 kg | $487 | 3 |
| Equal Angle Steel | 70 × 7 mm | Q235B | 36–37 kg | $487 | 1 |
| Equal Angle Steel | 70 × 7 mm | Q235B | 40–41 kg | $487 | 2 |
| Equal Angle Steel | 70 × 7 mm | Q235B | 40–42 kg | $487 | 2 |
| Equal Angle Steel | 70 × 8 mm | Q235B | 45–46 kg | $491 | 2 |
| Equal Angle Steel | 75 × 5 mm | Q235B | 28–29 kg | $487 | 3 |
| Equal Angle Steel | 75 × 5 mm | Q235B | 31–32 kg | $487 | 3 |
| Equal Angle Steel | 75 × 6 mm | Q235B | 33–35 kg | $487 | 4 |
| Equal Angle Steel | 75 × 6 mm | Q235B | 37–38 kg | $487 | 7 |
| Equal Angle Steel | 75 × 7 mm | Q235B | 43–44 kg | $487 | 3 |
| Equal Angle Steel | 75 × 8 mm | Q235B | 44–46 kg | $487 | 2 |
| Equal Angle Steel | 75 × 8 mm | Q235B | 49–50 kg | $487 | 3 |
| Equal Angle Steel | 75 × 10 mm | Q235B | 60–62 kg | $491 | 2 |
| Equal Angle Steel | 80 × 6 mm | Q235B | 35–36 kg | $487 | 4 |
| Equal Angle Steel | 80 × 6 mm | Q235B | 35–37 kg | $487 | 1 |
| Equal Angle Steel | 80 × 6 mm | Q235B | 39–41 kg | $487 | 3 |
| Equal Angle Steel | 80 × 8 mm | Q235B | 47–48 kg | $487 | 6 |
| Equal Angle Steel | 80 × 8 mm | Q235B | 52–54 kg | $487 | 2 |
| Equal Angle Steel | 80 × 10 mm | Q235B | 64–66 kg | $491 | 2 |
| Equal Angle Steel | 90 × 6 mm | Q235B | 40–42 kg | $487 | 3 |
| Equal Angle Steel | 90 × 6 mm | Q235B | 44–47 kg | $487 | 5 |
| Equal Angle Steel | 90 × 8 mm | Q235B | 52–55 kg | $490 | 1 |
| Equal Angle Steel | 90 × 8 mm | Q235B | 58–60 kg | $488 | 1 |
| Equal Angle Steel | 90 × 6 mm | Q235B | 67–70 kg | $487 | 3 |
| Equal Angle Steel | 90 × 8 mm | Q235B | 88–90 kg | $487 | 2 |
| Equal Angle Steel | 100 × 10 mm | Q235B | 109–111 kg | $487 | 3 |
| Equal Angle Steel | 100 × 10 mm | Q235B | 122–125 kg | $487 | 2 |
| Equal Angle Steel | 100 × 6 mm | Q235B | 50–52 kg | $487 | 27 |
| Equal Angle Steel | 100 × 8 mm | Q235B | 58–60 kg | $487 | 2 |
| Equal Angle Steel | 100 × 6 mm | Q235B | 68–70 kg | $487 | 1 |
| Equal Angle Steel | 100 × 10 mm | Q235B | 72–75 kg | $487 | 2 |
| Equal Angle Steel | 100 × 8 mm | Q235B | 99–102 kg | $487 | 4 |
| Equal Angle Steel | 110 × 8 mm | Q235B | 109–112 kg | $493 | 3 |
| Equal Angle Steel | 110 × 10 mm | Q235B | 135–138 kg | $493 | 2 |
| Equal Angle Steel | 125 × 8 mm | Q235B | 126–128 kg | $493 | 2 |
| Equal Angle Steel | 125 × 10 mm | Q235B | 154–158 kg | $493 | 1 |
Showing 96 of 96 listed sizes. Price range USD 485–524 per tonne (EXW China). MOQ from 1 tonne; stock dispatched to port within 3 days. Mill test certificate (EN 10204 3.1) and third-party inspection available on request.