Hot-Rolled I-Beam / Universal Beam (I10 – I63) | Q235B, Q355B, SS400
Hot-rolled I-beam (also called steel joist or H-beam by trade habit) in Q235B, Q355B and SS400, from I10 up to I63 in the a and b thickness series. Standard lengths 6 m, 9 m and 12 m, cut to length and bevelled on request, with a mill test certificate for every heat.
Product Overview
An I-beam is a hot-rolled structural section with two tapered flanges joined by a central web, and the shape is efficient because it puts most of the material where it resists bending — as far as possible from the neutral axis. For a given weight per metre it carries far more bending moment than a flat bar, an angle or a channel, which is why it is the default choice for beams, crane rails and machine bases.
The Chinese designation is by web height in centimetres, so I20 means a nominal web height of 200 mm. Each height is rolled in an a and a b version: the b version has a thicker web and wider flanges and therefore a higher section modulus, so a b section can be used where the a section would be marginal. The standard series runs from I10 to I63, and stock covers the common structural sizes from I10 up to I36 in both the a and b versions.
Grades supplied are Q235B to GB/T 700 for general structural work, Q355B to GB/T 1591 where a higher yield strength allows a lighter beam over a long span, and SS400 to JIS G3101 for buyers who specify to Japanese standards. Sections are supplied in 6 m, 9 m and 12 m lengths, cut to length and bevelled to your drawing, with mill test certificates and the option of hot-dip galvanizing on top.

Specifications & Size Range
Standard I-beam series with the a (standard web) and b (thicker web, wider flange) designations. Mill lengths are 6 m, 9 m and 12 m; cut-to-length and end bevelling are available. Larger and heavier sections in the same series are produced to order.
| Size group | Designations | Web height (mm) | Standard length | Typical use |
|---|---|---|---|---|
| Light beam | I10, I12, I14, I16, I18 | 100 – 180 | 6 m / 9 m | Purlins, floor beams, machine frames, light gantries |
| Medium beam | I20a / I20b, I22a / I22b, I24a / I24b, I25a / I25b | 200 – 250 | 9 m / 12 m | Building beams, crane rails, plant frames, skid bases |
| Heavy beam | I27a / I27b, I28a / I28b, I30a / I30b, I32a / I32b | 270 – 320 | 12 m | Long-span beams, gantry and crane girders, bridge members |
| Extra heavy beam | I36a / I36b and heavier sections up to I63 | 360 – 630 | 12 m, cut to order | Heavy industrial structures, tipplers, presses, bridge girders |
| Processed beam | Any size above | as above | cut and bevelled to drawing | Beams delivered ready for welding, with ends prepared as specified |
Tolerances
Dimensions, web and flange thickness, straightness and mass follow GB/T 706 for hot-rolled section steel, with the applicable tolerance band stated on the mill certificate and confirmed on the order acknowledgement. Length tolerance and end squareness are agreed per order, and where the beam will be welded into a connection the end preparation is defined on the order acknowledgement before production.
Available Sizes — Detailed Specification
Every size below has its own page with the full theoretical weight table, tolerances, grade data, applications and delivery options. Theoretical weights are the published values from GB/T 706-2016 Table A.1.
| Size | Web thickness | Weight (kg/m) | Specification page |
|---|---|---|---|
| 100 × 68 mm | 4.5 mm | 11.261 | Weight & specification |
| 120 × 74 mm | 5 mm | 13.987 | Weight & specification |
| 126 × 74 mm | 5 mm | 14.223 | Weight & specification |
| 140 × 80 mm | 5.5 mm | 16.89 | Weight & specification |
| 160 × 88 mm | 6 mm | 20.513 | Weight & specification |
| 180 × 94 mm | 6.5 mm | 24.143 | Weight & specification |
| 200 × 100 mm | 7 mm | 27.929 | Weight & specification |
| 200 × 102 mm | 9 mm | 31.069 | Weight & specification |
| 220 × 110 mm | 7.5 mm | 33.07 | Weight & specification |
| 220 × 112 mm | 9.5 mm | 36.524 | Weight & specification |
| 240 × 116 mm | 8 mm | 37.477 | Weight & specification |
| 240 × 118 mm | 10 mm | 41.245 | Weight & specification |
| 250 × 116 mm | 8 mm | 38.105 | Weight & specification |
| 250 × 118 mm | 10 mm | 42.03 | Weight & specification |
| 270 × 122 mm | 8.5 mm | 42.825 | Weight & specification |
| 270 × 124 mm | 10.5 mm | 47.064 | Weight & specification |
| 280 × 122 mm | 8.5 mm | 43.492 | Weight & specification |
| 280 × 124 mm | 10.5 mm | 47.888 | Weight & specification |
| 300 × 126 mm | 9 mm | 48.084 | Weight & specification |
| 300 × 128 mm | 11 mm | 52.794 | Weight & specification |
| 300 × 130 mm | 13 mm | 57.504 | Weight & specification |
| 320 × 130 mm | 9.5 mm | 52.717 | Weight & specification |
| 320 × 132 mm | 11.5 mm | 57.741 | Weight & specification |
| 320 × 134 mm | 13.5 mm | 62.765 | Weight & specification |
| 360 × 136 mm | 10 mm | 60.037 | Weight & specification |
| 360 × 138 mm | 12 mm | 65.689 | Weight & specification |
| 360 × 140 mm | 14 mm | 71.341 | Weight & specification |
| 400 × 142 mm | 10.5 mm | 67.598 | Weight & specification |
| 400 × 144 mm | 12.5 mm | 73.878 | Weight & specification |
| 400 × 146 mm | 14.5 mm | 80.158 | Weight & specification |
| 450 × 150 mm | 11.5 mm | 80.42 | Weight & specification |
| 450 × 152 mm | 13.5 mm | 87.485 | Weight & specification |
| 450 × 154 mm | 15.5 mm | 94.55 | Weight & specification |
| 500 × 158 mm | 12 mm | 93.654 | Weight & specification |
| 500 × 160 mm | 14 mm | 101.504 | Weight & specification |
| 500 × 162 mm | 16 mm | 109.354 | Weight & specification |
| 560 × 166 mm | 12.5 mm | 106.316 | Weight & specification |
| 560 × 168 mm | 14.5 mm | 115.108 | Weight & specification |
| 560 × 170 mm | 16.5 mm | 123.9 | Weight & specification |
| 630 × 176 mm | 13 mm | 121.407 | Weight & specification |
| 630 × 178 mm | 15 mm | 131.298 | Weight & specification |
| 630 × 180 mm | 17 mm | 141.189 | Weight & specification |
Steel Grades & International Equivalents
All grades below are supplied with a mill test certificate. The right-hand column shows the material type and the Chinese standard the grade is produced to; the middle columns give the nearest recognised equivalent in other national standards. Exact equivalence for a specific project should be confirmed on the enquiry.
| GB (China) | ASTM / AISI (US) | EN (Europe) | JIS (Japan) | DIN (Germany) | Type / Standard |
|---|---|---|---|---|---|
| Q235B | A36 / A283 Gr.C | S235JR (EN 10025-2) | SS400 (JIS G3101) | St37-2 | Carbon structural steel (GB/T 700) |
| Q355B | A572 Gr.50 / A992 | S355JR (EN 10025-2) | SM490 (JIS G3106) | St52-3 | High-strength low-alloy (HSLA) steel (GB/T 1591) |
| SS400 (JIS) | A36 | S235JR | SS400 | St37-2 | Carbon structural steel (JIS G3101) |
Grade Notes
- Q235B — The workhorse structural grade in China. Fully weldable, excellent cost-performance, the closest Chinese equivalent to ASTM A36 / EN S235JR.
- Q355B — High-strength structural steel for heavy structures, bridges and towers. Equivalent to ASTM A572 Gr.50 / EN S355JR.
- SS400 (JIS) — Japanese standard grade widely accepted in Asia. Interchangeable with Q235B / A36 for general structures.
Chemical Composition (%, ladle analysis)
Typical specification limits. Actual heat values are reported on the mill test certificate supplied with every shipment.
| Grade | C | Si | Mn | P max | S max | Other elements |
|---|---|---|---|---|---|---|
| Q235B | ≤0.20 | ≤0.35 | ≤1.40 | ≤0.045 | ≤0.045 | — |
| Q355B | ≤0.24 | ≤0.55 | ≤1.60 | ≤0.035 | ≤0.035 | Ceq ≤0.45 |
| SS400 (JIS) | — | — | — | ≤0.050 | ≤0.050 | — |
Mechanical Properties
Minimum values at room temperature unless stated. ReL = yield strength; Rp0.2 = 0.2% proof stress; Rm = tensile strength; A = elongation after fracture.
| Grade | Yield (ReL) | Proof (Rp0.2) | Tensile (Rm) | Elongation A | Impact / others | |
|---|---|---|---|---|---|---|
| Q235B | ≥235 MPa | — | 370–500 MPa | ≥26% | +20 °C, ≥27 J | — |
| Q355B | ≥355 MPa (≤16 mm) | — | 470–630 MPa | ≥22% | +20 °C, ≥27 J | — |
| SS400 (JIS) | ≥245 MPa | — | 400–510 MPa | ≥21% | — | — |

Standards & Documents
- GB/T 706 — hot-rolled section steel (I-beam dimensions, shape, mass and tolerance)
- GB/T 700 — carbon structural steels (Q235B: ReH ≥ 235 MPa, Rm 370–500 MPa)
- GB/T 1591 — high-strength low-alloy structural steels (Q355B: ReH ≥ 355 MPa to 16 mm, Ceq ≤ 0.45)
- JIS G3101 — rolled steels for general structure (SS400: ReH ≥ 245 MPa)
- EN 10025-2 / ASTM A36 / A572 Gr.50 / A992 — grade equivalences confirmed in writing on request
- EN 10204 3.1 mill test certificate with every lot; SGS or BV inspection and hot-dip galvanizing available
Typical Applications
| Industry / Application | Typical use |
|---|---|
| Industrial buildings & warehouse frames | Roof and floor beams, crane runway girders, mezzanine beams and column-free spans in factories, warehouses and distribution centres. |
| Crane girders & overhead handling | Runway beams, gantry legs and monorail supports, where the section is sized from the wheel load and the fatigue duty rather than from the static load alone. |
| Bridges & transport infrastructure | Highway bridge beams, footbridge frameworks, temporary works bridges and ramp supports, in Q235B or Q355B depending on the design code. |
| Machinery & equipment bases | Skid bases, press frames, crusher and conveyor supports and machine beds where stiffness under dynamic load matters as much as strength. |
| Port & material handling equipment | Ship-loader and stacker frames, transfer car rails and heavy handling structures that operate outdoors and are usually galvanized. |
| Temporary works & heavy supports | Propping, shoring, trestles and temporary road plates which are re-used and therefore benefit from bolted, adjustable connections. |
| Fabrication & repair workshops | General structural stock for fabricators who cut beams to length and weld them into built-up members or secondary steelwork. |
Common Problems Buyers Face — and How We Prevent Them
These are the issues that most often cause claims on steel imports. Each one is controlled in our process before shipment.
The beam deflects more than the design allowed
Why it happens: The a version has been substituted for the heavier b version of the same height, or a non-standard section has been shipped with thinner web and flange than the nominal designation.
Our control: The order acknowledgement states the full designation including the a or b suffix, and the mill certificate gives the actual web and flange thicknesses so the section properties can be verified against the design. Material is bought mill-certified only, and nominal-size or non-standard sections are never substituted silently.
Rust and pitting on the flanges before fabrication
Why it happens: Hot-rolled beams travel with mill scale and no coating, and a long sea voyage in humid air will start surface oxidation.
Our control: Material is shipped dry and covered with VCI paper on long routes. For beams that will be exposed during construction or storage, we supply shot-blasted and primed, or hot-dip galvanized sections.
Cracking or lamellar tearing at a welded connection
Why it happens: The grade selected has a carbon equivalent at the top of the band, or the flange thickness makes the through-thickness properties critical at a heavy welded joint.
Our control: The mill certificate reports actual chemistry including carbon equivalent, so the welding engineer can validate the procedure. Tell us at enquiry stage if the connection is heavily restrained or if through-thickness properties are required, and we will advise on a lower-Ceq option.
Beams arriving bent or twisted after handling
Why it happens: Long slender sections can sag or twist when they are stacked unsupported or lifted by a single point during transhipment.
Our control: Beams are bundled into stiff packs and lifted at two points with approved slings, and the stow is planned so the pack is supported along its length. Straightness is checked at loading against the standard for the section.
Lengths and end preparation not matching the fabrication shop
Why it happens: Beams ordered to a nominal length arrive square cut when the fabricator expected a bevelled end, or the length tolerance is wider than the shop allowed for.
Our control: Length, length tolerance and end preparation — square cut, bevelled, or cut to a template — are all confirmed in writing on the order acknowledgement and repeated on the bundle labels before production starts.

Our Supply & Manufacturing Advantages
- Structural efficiency per kilogram — The I-section puts material where it resists bending, so a beam carries the load with less steel than a flat bar, angle or channel doing the same job.
- The a and b series from one supplier — Both the standard and heavy-web versions are available in each height, so the design can be tuned to the load instead of being rounded up to the next size.
- Grades matched to the drawing — Q235B, Q355B and SS400 with written grade equivalence to A36, A572 Gr.50, S235JR and S355JR so the certificate satisfies your engineer.
- Processed before shipment — Cut to length and bevelled end preparation carried out in the works, which reduces offcuts, freight weight and fabrication time at your end.
- Documented material — EN 10204 3.1 mill test certificate with heat number, chemistry and mechanical properties for every lot, plus third-party inspection and coating reports on request.
- Export packing and realistic lead times — Bundled and strapped for container loading, or loose in a bulk vessel, with stock sizes dispatched to the port within 3 days.
Packaging, Delivery & Payment
- Packing: loose in bulk vessel, or bundled and containerised to your requirement. Galvanized and coated products get VCI paper, waterproof wrapping and edge protection. See our export packaging methods.
- Availability: both stock and custom production. Tell us the specification and we will confirm the route.
- MOQ: no strict minimum — one ton can ship.
- Lead time: stock dispatched to port within 3 days; orders needing export packaging about 1 week; custom production quoted per product.
- Payment: stock — 10% deposit, balance before shipment; custom production — 50% deposit, balance before shipment.
- Documents: EN 10204 3.1 mill test certificate with every shipment; third-party inspection (SGS / BV) on request.
Frequently Asked Questions
What is the Chinese equivalent of EN S355JR for an I-beam?
Q355B to GB/T 1591 is the equivalent grade, with a minimum yield strength of 355 MPa at thicknesses up to 16 mm, a tensile range of 470 to 630 MPa and an impact requirement of 27 J at +20 °C. We supply beams in Q355B and the mill certificate shows the chemistry and mechanical properties so the equivalence can be verified before fabrication.
What is the difference between an I-beam and an H-beam?
An I-beam has tapered flanges and a relatively narrow flange width, which makes it efficient in bending but less efficient for bolted connections. An H-beam (wide flange section) has parallel, wider flanges, so it carries more bending moment for a similar weight and is much easier to bolt and weld in a frame. I-beams are common in press and machinery work, H-beams in building frames and long-span structures.
What is the difference between the a and b designation, for example I20a and I20b?
Both have the same nominal web height of 200 mm, but the b version has a thicker web and wider flanges, so its section modulus and bending capacity are higher. Choose b where the a section is marginal on strength or deflection, or where the connection detail needs a wider flange. The mill certificate states the actual web and flange thickness so the section properties can be confirmed.
Should I choose Q235B or Q355B for a long-span beam?
For a long span, Q355B usually reduces the total steel weight because the higher yield strength allows a smaller or lighter section for the same bending moment. The trade-off is a tighter welding control requirement, since Q355B carries a carbon-equivalent limit of 0.45. Send us the span, the load and the deflection limit and we will compare both grades.
Who supplies hot-rolled I-beams from China for export projects?
We supply I-beams from I10 up to I63 in the a and b series, in Q235B, Q355B and SS400, with cut-to-length and end bevelling, EN 10204 3.1 mill certificates and export packing for container or bulk vessel. Send the section list, the grade and the destination port for a quotation including weights and packing.
What length tolerance applies to cut beams?
Mill standard lengths of 6 m, 9 m and 12 m carry the tolerance of the underlying standard. Cut-to-length beams are held to a tolerance agreed on the order acknowledgement, typically a few millimetres on a fabrication cut, and this is confirmed in writing before the material is cut.
Can the beams be supplied galvanized?
Yes. Beams can be hot-dip galvanized to EN ISO 1461 or ASTM A123 with a coating weight nominated against the site atmosphere, and they can be cut to length and bevelled before dipping so the ends and holes are fully coated.
Do you have a minimum order quantity for I-beams?
No strict minimum and one ton can ship, though for long heavy sections the freight economics strongly favour container or full-vessel quantities. Tell us the destination port and we will show you where the break point is.
How are I-beams packed and shipped?
Beams are bundled into stiff packs and strapped to container dimensions, or shipped loose in a bulk vessel for large tonnage. Contact points are protected with timber or rubber so flanges are not scored, and the stow is arranged so each pack is supported along its length for the whole voyage.
Request a Quotation Export Packaging
Live Stock & Indicative Price
The table below lists live stock at the time of publication, with indicative EXW China reference prices in USD per tonne (converted at 6.70 CNY/USD). Steel prices move with the mill market every week — send us your size, quantity and destination and we will confirm availability and issue a firm FOB or CIF quotation.
| Product | Size / Model | Grade | Weight / pc | Price (USD/t, EXW) | Stock |
|---|---|---|---|---|---|
| Hot-Rolled I-Beam | I100 | Q235 | 24–25 kg | $539 | 32 |
| Hot-Rolled I-Beam | I100 | Q235 | 36–38 kg | $507 | 2 |
| Hot-Rolled I-Beam | I100 | Q235 | 39–40.5 kg | $501 | 5 |
| Hot-Rolled I-Beam | I100 | Q235 | 41–42 kg | $499 | 7 |
| Hot-Rolled I-Beam | I100 | Q235 | 50–52 kg | $493 | 11 |
| Hot-Rolled I-Beam | I100 | Q235 | 54–55.5 kg | $493 | 1 |
| Hot-Rolled I-Beam | I100 | Q235 | 61–62 kg | $493 | 7 |
| Hot-Rolled I-Beam | I120 | Q235 | 29–30 kg | $542 | 15 |
| Hot-Rolled I-Beam | I120 | Q235 | 45–47 kg | $507 | 9 |
| Hot-Rolled I-Beam | I120 | Q235 | 47.5–49.5 kg | $501 | 7 |
| Hot-Rolled I-Beam | I120 | Q235 | 50–52 kg | $499 | 7 |
| Hot-Rolled I-Beam | I120 | Q235 | 62–64.5 kg | $493 | 27 |
| Hot-Rolled I-Beam | I120 | Q235 | 67–69 kg | $493 | 5 |
| Hot-Rolled I-Beam | I120 | Q235 | 75–78 kg | $493 | 10 |
| Hot-Rolled I-Beam | I140 | Q235 | 106–109 kg | $496 | 2 |
| Hot-Rolled I-Beam | I140 | Q235 | 112–117 kg | $493 | 17 |
| Hot-Rolled I-Beam | I140 | Q235 | 121–124 kg | $490 | 4 |
| Hot-Rolled I-Beam | I140 | Q235 | 137–140 kg | $490 | 1 |
| Hot-Rolled I-Beam | I140 | Q235 | 54.5–57 kg | $507 | 10 |
| Hot-Rolled I-Beam | I140 | Q235 | 57.5–60 kg | $501 | 4 |
| Hot-Rolled I-Beam | I140 | Q235 | 60.5–63 kg | $499 | 6 |
| Hot-Rolled I-Beam | I140 | Q235 | 70–73 kg | $496 | 9 |
| Hot-Rolled I-Beam | I140 | Q235 | 75–77 kg | $493 | 10 |
| Hot-Rolled I-Beam | I140 | Q235 | 81–84.5 kg | $490 | 8 |
| Hot-Rolled I-Beam | I160 | Q235 | 110–113.5 kg | $490 | 5 |
| Hot-Rolled I-Beam | I160 | Q235 | 136–142 kg | $493 | 6 |
| Hot-Rolled I-Beam | I160 | Q235 | 149–153 kg | $490 | 3 |
| Hot-Rolled I-Beam | I160 | Q235 | 45–47 kg | $542 | 17 |
| Hot-Rolled I-Beam | I160 | Q235 | 67–69 kg | $507 | 13 |
| Hot-Rolled I-Beam | I160 | Q235 | 70–73 kg | $501 | 10 |
| Hot-Rolled I-Beam | I160 | Q235 | 73.5–76.5 kg | $499 | 11 |
| Hot-Rolled I-Beam | I160 | Q235 | 84–88 kg | $496 | 9 |
| Hot-Rolled I-Beam | I160 | Q235 | 91–95 kg | $493 | 9 |
| Hot-Rolled I-Beam | I160 | Q235 | 99–102 kg | $490 | 6 |
| Hot-Rolled I-Beam | I180 | Q235 | 117–120 kg | $490 | 1 |
| Hot-Rolled I-Beam | I180 | Q235 | 152–156 kg | $496 | 1 |
| Hot-Rolled I-Beam | I180 | Q235 | 99–103 kg | $496 | 2 |
| Hot-Rolled I-Beam | I200 | Q235 | 100.5–104 kg | $499 | 8 |
| Hot-Rolled I-Beam | I200 | Q235 | 117–122 kg | $496 | 8 |
| Hot-Rolled I-Beam | I200 | Q235 | 124–127.5 kg | $493 | 3 |
| Hot-Rolled I-Beam | I200 | Q235 | 134–139 kg | $490 | 7 |
| Hot-Rolled I-Beam | I200 | Q235 | 150–154 kg | $490 | 4 |
| Hot-Rolled I-Beam | I200 | Q235 | 179–183 kg | $496 | — |
| Hot-Rolled I-Beam | I200 | Q235 | 188–194 kg | $493 | 7 |
| Hot-Rolled I-Beam | I200 | Q235 | 201-206kg. | $490 | 4 |
| Hot-Rolled I-Beam | I200 | Q235 | 70–72.5 kg | $527 | 30 |
| Hot-Rolled I-Beam | I200 | Q235 | 95.5–98 kg | $501 | 8 |
Showing 47 of 47 listed sizes. Price range USD 490–542 per tonne (EXW China). MOQ from 1 tonne; stock dispatched to port within 3 days. Mill test certificate (EN 10204 3.1) and third-party inspection available on request.