Hot-Dip Galvanized Steel Sheet & Coil (SGCC, DX51D, Z100-Z700)
Hot-dip galvanized steel sheet and coil in SGCC and DX51D+Z, from 0.3 mm to 4.0 mm and thicker on request, with zinc coatings from 30 to 700 g/m² on both surfaces. Widths 1000 mm, 1250 mm and 1500 mm, supplied as coil, slit strip or cut sheet, with a coating mass test report and mill test certificate with each lot.
Product Overview
Hot-dip galvanized sheet is made by passing cold-rolled or hot-rolled steel through a molten zinc bath, so that a metallurgically bonded zinc-iron coating forms across the whole surface. The coating is not a paint film: it protects the steel by sacrificial action, which means it continues to protect the cut edges and drilled holes where a coating film would have been broken. That is what makes galvanized sheet the standard material for roofing, ducting, panels and any part that will be exposed to weather or humidity.
Coating weight is the specification that decides service life, and it is quoted as the total on both surfaces. As a practical guide, 80 to 120 g/m² suits indoor and sheltered use; 120 to 275 g/m² covers general outdoor exposure and is the most common export specification; and 275 g/m² and above is used for coastal and industrial atmospheres where salt or pollution accelerates corrosion. Coating masses from 30 g/m² to 700 g/m² can be ordered, and the heavier coatings go on heavier base thicknesses.
The surface finish is skin-passed and non-spangled, which gives a uniform, smooth, lightly oiled surface that takes paint, powder coating, printing and adhesive without preparation. It is also the finish that roll-forming, ducting and appliance lines expect. Sheet is available as coil for your own line, as strip slit to the width you feed, or as cut sheet in the size you use, and the coating is inspected and reported in grams per square metre rather than described loosely as standard galvanized.

Specifications & Size Range
Base thickness, coating weight and supply form. Coating weight is quoted as the total on both surfaces, with about 7 microns of coating thickness for every 100 g/m². Widths 1000 mm and 1250 mm are common in the thin gauges and 1250 mm and 1500 mm in the heavier gauges; cut sheet is normally 2000 mm or 2500 mm long.
| Base thickness (mm) | Common coating weights (g/m²) | Width (mm) | Supply form | Typical use |
|---|---|---|---|---|
| 0.3, 0.4, 0.5, 0.6 | 80 / 120 / 275 | 1000 / 1250 | coil, slit strip or cut sheet | Ducting, appliance casings, light panels, sign blanks |
| 0.7, 0.75, 0.8, 0.9, 1.0 | 80 / 120 / 275 | 1000 / 1250 | coil, slit strip or cut sheet | Roofing and cladding, cable trays, ventilation, fascia |
| 1.1, 1.2, 1.4, 1.5, 1.8 | 80 / 120 / 275 | 1000 / 1250 / 1500 | coil or cut sheet | Structural panels, machine casings, enclosure bodies |
| 1.9, 2.0, 2.3, 2.5, 2.75 | 120 / 275 / heavier on request | 1250 / 1500 | coil or cut sheet | Heavy ducting, gutter and flashing, trailer panels |
| 3.0, 3.5, 3.75, 4.0, up to 5.75 | 120 / 275 / 350 and above | 1250 / 1500 | coil or cut sheet | Walkway and platform plate stock, heavy enclosures, marine trim |
Tolerances
Coating mass to GB/T 13912, ISO 1461, EN 10346 and ASTM A653, quoted in g/m² total on both surfaces, with a working guide of about 7 microns of coating thickness per 100 g/m². Coating mass and adhesion are tested on a sample basis per lot and a coating test report travels with the shipment. Base sheet thickness follows the relevant cold-rolled or hot-rolled standard, and flatness, width and length tolerance are confirmed on the order acknowledgement.
Theoretical Weight Table — Galvanized Steel Sheet
The weights below are theoretical values calculated from nominal dimensions at a steel density of 7.85 g/cm³, to GB/T 2518 / EN 10346. For plate: W (kg/m²) = t × 7.85. They are used for estimating tonnage and freight; for commercial settlement the actual weighed mass applies, and the basis (theoretical or actual) is agreed on the order. Need a size that is not listed, or a cut length? Send us the size and quantity and we will confirm weight, price and delivery.
Thicknesses follow the GB/T 709-2019 nominal series.
| Thickness (mm) | Weight (kg/m²) | Weight, 1500 × 6000 sheet (kg) |
|---|---|---|
| 3 | 23.55 | 211.9 |
| 4 | 31.4 | 282.6 |
| 5 | 39.25 | 353.2 |
| 6 | 47.1 | 423.9 |
| 8 | 62.8 | 565.2 |
| 10 | 78.5 | 706.5 |
| 12 | 94.2 | 847.8 |
| 14 | 109.9 | 989.1 |
| 16 | 125.6 | 1130.4 |
| 18 | 141.3 | 1271.7 |
| 20 | 157 | 1413 |
| 25 | 196.25 | 1766.2 |
| 30 | 235.5 | 2119.5 |
| 40 | 314 | 2826 |
| 50 | 392.5 | 3532.5 |
| 60 | 471 | 4239 |
16 sizes listed. The full range including intermediate sizes is available on request.
Steel Grades & International Equivalents
All grades below are supplied with a mill test certificate. The right-hand column shows the material type and the Chinese standard the grade is produced to; the middle columns give the nearest recognised equivalent in other national standards. Exact equivalence for a specific project should be confirmed on the enquiry.
| GB (China) | ASTM / AISI (US) | EN (Europe) | JIS (Japan) | DIN (Germany) | Type / Standard |
|---|---|---|---|---|---|
| SGCC (galvanized sheet) | A653 CS Type B | DX51D+Z (EN 10346) | SGCC | DA01+Z | Hot-dip zinc-coated steel sheet (JIS G3302) |
| DX51D+Z | A653 CS | DX51D+Z | SGCC | DX51D+Z | Hot-dip zinc-coated steel sheet (EN 10346) |
| Zinc coating | A123 / A153 / A653 | EN ISO 1461 / EN 10346 | JIS H8641 | DIN 50976 | Hot-dip zinc coating specification (GB/T 13912) |
Grade Notes
- SGCC (galvanized sheet) — Standard commercial galvanized sheet for ducting, panels, roofing and appliance parts.
- DX51D+Z — European-grade zinc-coated sheet with excellent forming and bending properties.
- Zinc coating — Coating weight is quoted in g/m² total on both surfaces. Heavier coatings suit marine, coastal and high-humidity routes.
Chemical Composition (%, ladle analysis)
Typical specification limits. Actual heat values are reported on the mill test certificate supplied with every shipment.
| Grade | C | Si | Mn | P max | S max | Other elements |
|---|---|---|---|---|---|---|
| SGCC (galvanized sheet) | ≤0.15 | — | ≤0.60 | ≤0.050 | ≤0.050 | — |
| DX51D+Z | ≤0.18 | — | ≤1.20 | ≤0.120 | ≤0.045 | — |
Mechanical Properties
Minimum values at room temperature unless stated. ReL = yield strength; Rp0.2 = 0.2% proof stress; Rm = tensile strength; A = elongation after fracture.
| Grade | Yield (ReL) | Proof (Rp0.2) | Tensile (Rm) | Elongation A | Impact / others | |
|---|---|---|---|---|---|---|
| SGCC (galvanized sheet) | ≥205 MPa | — | 270–500 MPa | ≥20% | — | Coating Z100–Z700 (g/m² total both sides) |
| DX51D+Z | 140–320 MPa | — | 270–500 MPa | ≥18% | — | Coating Z100–Z600 (g/m² total both sides) |
| Zinc coating | — | — | — | — | — | Coating Mass 30 / 60 / 100 / 150 / 200 / 275 / 300 / 500 / 700 g/m², made to order Thickness Guide ≈7 µm per 100 g/m² (both sides) Salt Spray typ. 500–1500 h to red rust, coating-weight dependent |

Standards & Documents
- JIS G3302 — hot-dip zinc-coated steel sheet and strip (SGCC: coating designation and mechanical properties)
- EN 10346 — continuously hot-dip coated steel flat products (DX51D+Z)
- ASTM A653 — steel sheet, zinc-coated by the hot-dip process (CS Type B equivalent)
- GB/T 13912 and ISO 1461 — hot-dip zinc coatings: coating mass and adhesion requirements
- Zinc bath to EN 1179 (Zn 99.995 per cent minimum); coating weights quoted as g/m² total on both surfaces
- EN 10204 3.1 mill test certificate with heat number, chemistry and mechanical properties, plus a coating mass test report
Typical Applications
| Industry / Application | Typical use |
|---|---|
| Roofing & wall cladding | Base sheet for profiled roofing, wall cladding, ridge and trim, gutter and flashing, where the coating has to survive decades of weather without maintenance. |
| Ventilation & ducting | Air-conditioning duct, exhaust and smoke duct, duct fittings and supports, where galvanized sheet is the standard material and the smooth surface keeps air resistance low. |
| Panels, enclosures & cabinets | Electrical and control cabinets, distribution boards, outdoor enclosures, machine guards and casings, where the coating protects both the visible face and the cut edges. |
| Appliance & equipment casings | Outer casings and back panels for air-conditioners, refrigerators and washing machines, and housings for industrial equipment, usually finished with powder coating over the galvanized surface. |
| Light steel framing & cold-formed parts | Cold-formed sections, purlins, studs, cable trays and roll-formed profiles produced from galvanized coil or slit strip. |
| Agricultural & livestock buildings | Roof and wall sheet, feeding and ventilation equipment, and grain store linings, where humidity and ammonia make an uncoated surface unsuitable. |
| Trailers, containers & vehicle panels | Trailer side and floor panels, container linings and vehicle trim, where the coating takes abrasion and road spray without a painted finish. |
Common Problems Buyers Face — and How We Prevent Them
These are the issues that most often cause claims on steel imports. Each one is controlled in our process before shipment.
White rust on the galvanized surface on arrival
Why it happens: Zinc reacts with moisture when air cannot circulate between stacked sheets or coils, producing wet-storage stain. It is a surface product rather than a loss of coating, but it looks like a defect at the receiving inspection.
Our control: Sheet and coil are shipped dry with spacers, interleaving and desiccant so air can move between layers, and on long or humid routes we pack with VCI paper. Where appearance is critical, ask for a passivation treatment, which suppresses wet-storage stain.
The coating is thinner than specified at some points
Why it happens: Coating weight varies across the width and along the coil, and a single spot reading can fall below the specification even when the average passes.
Our control: Coating mass is measured on a sample basis per lot and reported in g/m² against the standard, with the average and the individual-reading rule understood before the order is placed. The coating test report is issued with the mill certificate.
The galvanized surface will not accept paint properly
Why it happens: A freshly galvanized, lightly oiled surface and a poorly chosen primer are the usual cause of paint flaking or peeling, and the problem appears weeks after the finishing line has run.
Our control: Tell us if the sheet will be painted. We supply the non-spangled, skin-passed finish that takes coating systems reliably, advise on surface preparation, and can supply a passivated or chromate-treated surface where your paint system requires it.
Cut edges rusting while the flat faces stay bright
Why it happens: Galvanized sheet protects cut edges by sacrificial action rather than by coating them, so a heavily exposed cut edge will show red rust before the faces do.
Our control: For exposed edges use a heavier coating or specify hot-dip galvanized material instead of coated sheet, since hot-dip galvanizing coats the cut edge as well. Where sheet is cut on site, we can supply the correct zinc-rich touch-up material with the shipment.
Forming cracks or coating flaking in a tight bend
Why it happens: The coating and the base metal have different ductility, so a very tight bend radius will craze or flake the coating even when the base sheet forms without cracking.
Our control: Send the bend radius and the forming operation with the enquiry. We nominate the base thickness, the coating weight and, where the part is tight, a forming-grade substrate, so the coating survives the bend rather than being repaired afterwards.

Our Supply & Manufacturing Advantages
- Coating specified in grams, not adjectives — Coating weight is quoted in g/m² total on both surfaces, from 30 to 700 g/m², and matched to the atmosphere the part will actually see.
- Coil, slit strip or cut sheet — One order can arrive as coil for your own line, as strip slit to the width you feed, or as cut sheet in your size, which removes slitting and shearing from your process.
- Paintable surface as standard — The skin-passed, non-spangled finish takes paint, powder coating and adhesive without preparation, so a galvanized part can double as a painted part.
- Two standard grade families — SGCC to JIS G3302 for Asian and general markets, and DX51D+Z to EN 10346 for European specifications, with the equivalence stated on the certificate.
- Coating documentation — Coating mass test report plus an EN 10204 3.1 mill test certificate for every heat, with third-party inspection by SGS or BV available on request.
- Export packaging that protects the coating — Coils on timber saddles, sheet bundles with interleaving and edge protection, shipped dry so the coating arrives intact and free of wet-storage stain.
Packaging, Delivery & Payment
- Packing: loose in bulk vessel, or bundled and containerised to your requirement. Galvanized and coated products get VCI paper, waterproof wrapping and edge protection. See our export packaging methods.
- Availability: both stock and custom production. Tell us the specification and we will confirm the route.
- MOQ: no strict minimum — one ton can ship.
- Lead time: stock dispatched to port within 3 days; orders needing export packaging about 1 week; custom production quoted per product.
- Payment: stock — 10% deposit, balance before shipment; custom production — 50% deposit, balance before shipment.
- Documents: EN 10204 3.1 mill test certificate with every shipment; third-party inspection (SGS / BV) on request.
Frequently Asked Questions
How thick should the zinc coating be for my project?
As a working guide: 80 to 120 g/m² is adequate for dry indoor and sheltered service; 120 to 275 g/m² suits general outdoor exposure and is the most common export specification; and 275 g/m² and above is used for coastal, marine and industrial atmospheres. The figure is the total on both surfaces, and coating thickness is about 7 microns per 100 g/m². Tell us where the structure will stand and we will nominate the coating weight.
What is the difference between hot-dip galvanized and electro-galvanized sheet?
Hot-dip galvanized sheet is passed through molten zinc and carries a thicker, alloyed coating that protects by sacrificial action, so it suits outdoor and cut-edge exposure. Electro-galvanized sheet is plated in a zinc solution, giving a thinner and smoother coating with a brighter appearance, which is normally specified for indoor parts where appearance and paint finish dominate. For anything standing outside, hot-dip is the correct choice.
What is the Chinese or Japanese equivalent of DX51D+Z?
DX51D+Z to EN 10346 and SGCC to JIS G3302 are the two standard continuously galvanized sheet grades. They are close in chemistry, mechanical properties and coating designation, and SGCC is routinely accepted where DX51D+Z is specified, and vice versa. ASTM A653 CS Type B is the nearest American equivalent. We can supply the mill certificate with the equivalence stated for your records.
What is the difference between Z100 and Z275 coating?
The number is the coating mass in grams per square metre total on both surfaces, so Z100 carries 100 g/m² and Z275 carries 275 g/m². Roughly, Z100 gives about 7 microns of coating per face and suits sheltered or indoor use, while Z275 gives about 19 microns per face and is the common specification for outdoor and coastal service.
Can galvanized sheet be welded?
It can be welded, but the zinc coating vaporises at welding temperature, so the weld zone loses its protection and must be repaired with zinc-rich paint. Resistance welding of thin coated sheet requires higher current and electrode maintenance. For heavily welded assemblies, fabricate from uncoated steel and hot-dip galvanize the finished part, which coats the welds as well.
Who supplies galvanized steel sheet and coil from China for export?
We do. Galvanized sheet and coil are bought from major Chinese mills in SGCC and DX51D+Z, with coating weights from 30 to 700 g/m², and shipped worldwide with a mill test certificate and a coating mass test report. Send the base thickness, width, coating weight and quantity and we will confirm availability.
Why has white rust appeared on my galvanized sheet?
White rust, or wet-storage stain, forms when moisture is trapped between stacked sheets or coil wraps so that air cannot circulate. It is a zinc corrosion product on the surface, not a loss of coating thickness, and it does not reduce protection. It is avoided by shipping dry with spacers and desiccant, and prevented during storage by keeping the material dry and letting air circulate.
Do you have a minimum order quantity and what is the lead time?
There is no strict minimum and one ton can ship. Common sizes reach the port within about 3 days; orders requiring slitting, cut-to-length, passivation or protective packing take about a week. Non-standard coating weights and widths are quoted per item.
What documents are supplied with a galvanized sheet shipment?
An EN 10204 3.1 mill test certificate with heat number, chemical composition and mechanical properties, together with a coating mass test report showing the coating weight in g/m². The commercial invoice, packing list and certificate of origin are included, and third-party inspection can be arranged before loading.
Request a Quotation Export Packaging
Live Stock & Indicative Price
The table below lists live stock at the time of publication, with indicative EXW China reference prices in USD per tonne (converted at 6.70 CNY/USD). Steel prices move with the mill market every week — send us your size, quantity and destination and we will confirm availability and issue a firm FOB or CIF quotation.
| Product | Size / Model | Grade | Coating | Price (USD/t, EXW) | Stock |
|---|---|---|---|---|---|
| Galvanized Steel Sheet (skin-passed) | 0.4 × 1250 mm | — | Z80 | $670 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.5 × 1000 mm | — | Z120 | $670 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.5 × 1250 mm | — | Z120 | $660 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.5 × 1250 mm | — | Z275 | $869 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.5 mm | — | Z80 | $616 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.6 × 1250 mm | — | Z120 | $645 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.6 × 1250 mm | — | Z275 | $839 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.6 × 1250 mm | — | Z80 | $601 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.7 × 1250 mm | — | Z120 | $643 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.7 × 1250 mm | — | Z275 | $799 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.7 × 1250 mm | — | Z80 | $601 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.75 × 1250 mm | — | Z120 | $624 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.75 × 1250 mm | — | Z275 | $799 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.75 mm | — | Z80 | $588 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.8 × 1250 mm | — | Z120 | $619 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.8 mm | — | Z275 | $769 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.8 mm | — | Z80 | $588 | Ample |
| Galvanized Steel Sheet (skin-passed) | 0.9 × 1250 mm | — | Z80 | $578 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1 × 1250 mm | — | Z120 | $588 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1 × 1000 mm | — | Z120 | $597 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1 × 1000 mm | — | Z275 | $678 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1 × 1250 mm | — | Z275 | $675 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1 mm | — | Z275 | $699 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1 mm | — | Z80 | $564 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1 × 1500 mm | — | Z80 | $599 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.1 × 1250 mm | — | Z80 | $564 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.2 × 1000 mm | — | Z120 | $610 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.2 × 1000 mm | — | Z275 | $649 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.2 × 1250 mm | — | Z275 | $649 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.2 mm | — | Z275 | $672 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.2 mm | — | Z80 | $564 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.2 × 1500 mm | — | Z80 | $596 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.4 mm | — | Z80 | $564 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.4 × 1500 mm | — | Z80 | $596 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.5 × 1000 mm | — | Z275 | $649 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.5 × 1250 mm | — | Z275 | $637 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.5 mm | — | Z275 | $657 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.5 mm | — | Z80 | $564 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.5 × 1500 mm | — | Z80 | $591 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.75 × 1500 mm | — | Z80 | $591 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.8 × 1250 mm | — | Z100 | $566 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.8 × 1250 mm | — | Z275 | $627 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.8 mm | — | Z80 | $564 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.8 × 1500 mm | — | Z80 | $581 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1.9 × 1250 mm | — | Z80 | $564 | Ample |
| Galvanized Steel Sheet (skin-passed) | 2 × 1500 mm | — | Z120 | $585 | Ample |
| Galvanized Steel Sheet (skin-passed) | 2 × 1000 mm | — | Z275 | $627 | Ample |
| Galvanized Steel Sheet (skin-passed) | 2 × 1250 mm | — | Z275 | $615 | Ample |
| Galvanized Steel Sheet (skin-passed) | 2 mm | — | Z275 | $610 | Ample |
| Galvanized Steel Sheet (skin-passed) | 2 × 1250 mm | — | Z80 | $564 | Ample |
| Galvanized Steel Sheet (skin-passed) | 2 × 1500 mm | — | Z80 | $581 | Ample |
| Galvanized Steel Sheet (skin-passed) | 2.3 × 1500 mm | — | Z120 | $585 | Ample |
| Galvanized Checkered Plate | 2.5 × 1500 mm | — | Z120 | $619 | Ample |
| Galvanized Steel Sheet (skin-passed) | 2.5 mm | — | Z275 | $601 | Ample |
| Galvanized Steel Sheet (skin-passed) | 2.75 mm | — | Z120 | $576 | Ample |
| Galvanized Checkered Plate | 2.75 × 1500 mm | — | Z120 | $612 | Ample |
| Galvanized Steel Sheet (skin-passed) | 2.75 × 1250 mm | — | Z275 | $597 | Ample |
| Galvanized Steel Sheet (skin-passed) | 3 × 1250 mm | — | Z120 | $573 | Ample |
| Galvanized Checkered Plate | 3 × 1500 mm | — | Z120 | $612 | Ample |
| Galvanized Steel Sheet (skin-passed) | 3 mm | — | Z275 | $594 | Ample |
| Galvanized Steel Sheet (skin-passed) | 3.5 × 1500 mm | — | Z120 | $575 | Ample |
| Galvanized Steel Sheet (skin-passed) | 3.7 × 1250 mm | — | Z275 | $603 | Ample |
| Galvanized Steel Sheet (skin-passed) | 3.75 mm | — | Z120 | $581 | Ample |
| Galvanized Checkered Plate | 3.75 × 1500 mm | — | Z120 | $612 | Ample |
| Galvanized Steel Sheet (skin-passed) | 3.75 × 1500 mm | — | Z275 | $603 | Ample |
| Galvanized Steel Sheet (skin-passed) | 3.95 mm | — | Z120 | $581 | Ample |
| Galvanized Steel Sheet (skin-passed) | 3.95 × 1500 mm | — | Z275 | $603 | Ample |
| Galvanized Checkered Plate | 4.48 × 1500 mm | — | Z120 | $634 | Ample |
| Galvanized Checkered Plate | 4.75 mm | — | Z120 | $634 | Ample |
| Galvanized Steel Sheet (skin-passed) | 5.5/5.75*1250/1500 | — | Z120 | $594 | Ample |
| Galvanized Checkered Plate | 5.75 × 1250 mm | — | Z120 | $649 | Ample |
| Galvanized Steel Sheet (skin-passed) | 1250 mm | — | Z120 | $585 | Ample |
Showing 72 of 72 listed sizes. Price range USD 564–869 per tonne (EXW China). MOQ from 1 tonne; stock dispatched to port within 3 days. Mill test certificate (EN 10204 3.1) and third-party inspection available on request.